Rice-lake 880 Performance Series Indicator/Controller Techni Manual do Utilizador descarregar pdf (Página 78)

72 880 Technical/Service Manual

Setpoints Menu

Note

Table 6-16. Setpoints EDP Commands

Command Menu Description Choices / Range

SP.ACCESS#n ACCESS Setpoint access in top level

menu (user) OFF, ON

SP.BANDVAL#n BNDVAL Band value 0 - 999999

SP.BRANCH#n BRANCH Branch destination 0,1-20

SP.CLRACCM#n CLRACM Clear accumulator OFF, ON

SP.CLRTAR#n CLRTAR Clear tare OFF, ON

SP.DIGOUT#n DIGOUT Lists all digital output bits available for the

specified SLOT

NONE, BIT1 – BIT4

SP.END#n END Ending setpoint number for TIMER and CONCUR 1- 20

SP.HYSTER#n HYSTER Hysteresis Range:

0 - 65535 (for the COUNTR and

DEL

AY setpoints)

0 - 999999 (for the GROSS,

NET

, and %REL setpoints)

SP.KIND#n Selection made

rectly after

dropping down

from SETPT x

Supported setpoint kinds OFF, GROSS, NET, -GROSS,

-NET, %REL, PAUSE, DELAY,

WAITSS, COUNTR, AUTJOG,

TIMER, CONCUR

SP.BATSEQ#n BATSEQ Specifies whether the setpoint is a batch step OFF, ON

SP.NAME#n NAME Setpoint name string Alphanumeric, Max Length: 6

SP.PCOUNT#n PCOUNT Preact learn interval (number of cycles before it

earns)

Range: 0 - 65535

SP.PREACT#n PREACT Preact type OFF, ON, LEARN

SP.PREADJ#n PREADJ Preact adjustment percentage Range: 0 – 999999

SP.PRESTAB#n PRESTB Preact learn stability Range: 0 - 65535

SP.PREVAL#n PREVAL Preact value Range: 0 - 999999

SP.PSHACCM#n PSHACM Push accumulate OFF, ON, ONQUIET

SP.PSHPRINT#n PSHPRT Push print OFF, ON, WAITSS

SP.PSHTARE#n PSHTAR Push tare OFF, ON

SP.RELNUM#n RELNUM Relative setpoint number 1- 20

SP.SENSE#n SENSE Digital output sense NORMAL, INVERT

SP.DSLOT#n SLOT Digital output slot NONE, SLOT0, SLOT1

SP.START#n START Starting setpoint number for

TIMER and CONCUR 1- 20

SP.TRIP#n TRIP Specifies when the setpoin

t is satisfied when

compared to value

HIGHER, LOWER, INBAND,

OUTBAND

SP.VALUE#n VALUE Setpoint value Range:

0 - 65535 (for the COUNTR

d DELAY setpoints)

0 - 999999 (for the GROSS,

NET

, and %REL setpoints)

BATCHNG BATCHG Batching enable OFF, AUTO, MANUAL

Note

For setpoint commands the “n” symbolizes the setpoint number, 1-20.

Different setpoint parameters are available and accepted depending

on KIND, TRIP, and PREACT. These

restrictions are listed below by the EDP command

name but the same applies to access by menu.

1 2 ... 73 74 75 76 77 78 79 80 81 82 83 ... 119 120

Comentários a estes Manuais

Sem comentários

Rice-lake 880 Performance Series Indicator/Controller Techni Manual do Utilizador Página 78

Comentários a estes Manuais

Manuais e produtos relacionados com Balanças Rice-lake 880 Performance Series Indicator/Controller Techni