Rice-lake DWM-IV Weighmeter Standard Operators Manual Manual do Utilizador Página 1

113873DWM-IVDigital WeightmeterOperator Manual

Operating InstructionsA. DISPLAYThe display indicates the arithmetic result of the analog signal derived from the scalebase. The display indicates: OL

3. [Gross/Net] Button: If a tare has been entered, this button will alternately selectbetween the gross and net weight modes. If the tare has been cle

D. FRONT PANEL FUNCTIONSTEST  Allows the operator to test the integrity of the weight display by sequentiallylighting each segment of all digits, all

SUBTOTAL  The DWM-IV contains ten (10) registers for weight accumulation. Thesubtotal of all previously recorded weights or pieces may be recalled an

Front Panel Data EntrySelect the desired function from the examples given below. Then pressthe buttons in the order shown from left to right. The foll

FUNCTION 2: DRIBBLE entry of weight values.Dribble1Dribble2Dribble3FUNCTION 3: PREACT entry of weight values. Two speed feedenabled.Preact1Preact 2Pre

FUNCTION 4: T/D Time and Date Entry - 24 Hour Mode.Date TimeFUNCTION 5: SUBTOTAL Subtotal viewing or printing of selectedregister.orReg #PrintsSubtota

FUNCTION 8: CONSECUTIVE NUMBERING CN viewing orchanging.CNFUNCTION 9: PIECE WEIGHT Weight per Piece Entry and PieceMode Selection. Note: Selecting Reg

How to Enter and Exit System SetupLocate the small dip switch block in the lower right corner of the mother board. Turn onS1, the display should then

F6 Calibration, capacity and increment size selection.F7 Only available on custom systems.Configuration Setting DescriptionsF1.0 Raw Counts DisplayEna

Used to control the automatic ZEROING of the scale. It will automatically track smalldrifts in weight such as caused by small amounts of debris, rain,

F2.2 Auto Clear TareCauses the tare value to be cleared automatically when the scale returns to zero. Use thisto force entry of a new tare weight for

When this setting is enabled, only the fast feed relay is initially energized. The fast feedrelay is de-energized and the slow feed relay is simultane

F3.4 Consecutive Number PrintF3.5 ID PrintControls whether or not these items will be included in the data sent out of the serial port(such as to a pr

F4.1 Continuous Data FormatSelects the data format used for continuous data output. Normally used for remotedisplays and scoreboards and in some compu

weight and tare} should be used when communicating with a computer. It containsinformation on the current modes and status of the system sufficient to

F5.3 Total/SubTotalEnables the front panel [TOTAL] and [SUBTOTAL] buttons. This allows you to viewand clear totals data.F5.4 Time and DateEnables the

normally approximately 20,000 counts. To compute the number of counts divide the setcapacity by the increment size.F6.3 Enter Cal ModeThis is how you

E - Display the internal raw counts.F1.1 Digital AveragesNumber of A/D conversions which comprise the running average.Choices: 1, 2, 4, 8, 16, 32F1.2

F1.8 Output Optionsd - Neither of the following options installed.1 - Analog output card installed.2 - BCD output card installed.F1.9 High Resolution

F2.5 Enter Stand-By Mode on Power-Up Enabled - Weight indication appears after display test.E - Weight display will be disabled and all status indicat

FSE F3F3.0 Baud Rate Selection X100Select the desired BAUD rate according to the chart. Older DDO boards have a limitedrating on the current loop port

F3.5 ID Print Enabled - Disable the printing of the ID.E - Enable the printing of the ID.F3.6 Negative Print Enabled - Disable printing of negative we

2 - Print will occur if not in motion and positive at the time Print button is pressed.3 - Auto print after motion and positive weight is above value

F4.6 Time/Date Print Formatd - Time/Date printing disabled.1 - Time then Date printed.2 - Date then Time printed.3 - Time only printed.4 - Date only p

6 - ID, Time/Date, CN Total7 - ID Time/Date CN, TotalC - Custom Totals Print Format EnableF4.9 Weight Accumulation Enabled - Disable weight accumulati

F5.5 Presets Enabled - Preset, Dribble, and Preact disabled.E - Preset, Dribble, and Preact enabled.F5.6 Recall Tare Enabled - Recall Tare entry disab

1- .X2 - .XX3 - .XXX4 - .XXXXF6.3 Enter CAL Moded - Continue to last step (CAL d)E - Enter CAL mode.F6.4 Linearity FactorCorrects non-linearity in wei

[PRINT] - Advances to next step if span must be set.[TARE] - Establishes a new zero calibration setting without changing the spancalibration previousl

FILEd The programmed data will have been saved or discarded after this messageis displayed. Return the CAL switch S1 to the OFF position and the displ

Programming Steps SummaryRecord the final settings for each step in the boxes ([ ]) below for future reference.[ ]F1.0 Raw Counts Display Enable[ ]F1.

[ ]F2.7 Two Speed Feed Enable[ ]F2.8 Sequential Feed Enable[ ]F2.9 Invert Relays Enable[ ]F2.A Parallel Feed Enable*[ ]F2.B*[ ]F2.C*[ ]F2.D[ ]F3.0 Bau

[ ]F4.3 Minimum Print in Digits[ ]F4.4 Computer Communications[ ]F4.5 Weight Data Format[ ]F4.6 Time/Date Print Format[ ]F4.7 Weight Print Format[ ]F4

[ ]F6.2 Decimal Position[ ]F6.3 Enter CAL Mode[ ]F6.4 Linearity Factor*[ ]F7.0*[ ]F7.1*[ ]F7.2*[ ]F7.3*[ ]F7.4*[ ]F7.5*[ ]F7.6*[ ]F7.7*[ ]F7.8*[ ]F7.9

Remote Control InputsThe functions of ZERO, TARE, GROSS/NET, selection and PRINT may beperformed remotely via voltage-free contacts across the indicat

described, the user may program up to three (3) preamble characters that are sentafter the STX character and up to three (3) postamble characters whic

SPASCII character space (20h).CRASCII character carriage return (0Dh).LFASCII character line feed (0Ah).A. Displayed Weight OnlyGross wt OnlyNet wt On

D. Status, Weight and TareStatus Words TableBit STATU S A STATUS B STATUS C8 7 0 0 Relay 84 6 Center Zero Print Key Relay 72 5 Motion Decimal pos Rela

0 1 1 XXXX.XX1 0 0 XXX.XXX1 0 1 XX.XXXX4. Print Key = 1 if front panel PRINT key is being pressed.5. Relay = 1 if relay energized.6. Each Status Word

I) Z660 ScoreboardJ) ASCII - with Preamble and Postamble (No STX or ETX)K) RDCustom Print Format ProgrammingBy selecting the custom print options, it

total of eighty (80) codes may be entered. It is possible to print out particularheaders or titles by using the ASCII representations for them in deci

136Internal code for carriage return-line feed and checksum insertion if enabled. Donot use.137Inserts the previously entered postamble entered under

9 65 A 32 255 Ends Print Field 5510 77 M 33 132 5611 69 E 34 10 5712 32 35 13 5813 72 H 36 131 5914 69 E 37 10 6015 82 R 38 13 6116 69 E 39 130 6217 4

Page 53

Page 54

Page 55

Data Output: Serial ASCII 20 mA current loop with selectable baud rates (15019.2K),selectable auto or manual print, continuous data out, or bi-direct

VT 11 00001011 013 0B K 75 01001011 113 4B TA11FF 12 00001100 014 0C L 76 01001100 114 4C TA12CR 13 00001101 015 0D M 77 01001101 115 4D TA13SO 14 000

. 46 00101110 056 2E LA14 n 110 01101110 156 6E SC14/ 47 00101111 057 2F LA15 o 111 01101111 157 6F SC150 48 00110000 060 30 LA16 p 112 01110000 160 7

DWM-IV Limited WarrantyRice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly installed by a Distributor or Original

Over Capacity: Displays OLOADat 102% of Full Scale Capacity.Center Zero: Light indication when scale is within +/-0.25 digit of center of zero (0).Loa

Installation RequirementsMaximum performance is guaranteed only when installation of the scale system isperformed by a qualified scale technician. For